Industrial grade two part textured non slip epoxy coating designed for application to any type of floors that operate in wet environments with slippery conditions. This coating offers the ultimate in slip prevention and durability on Oil Rigs, Ships, Wineries, Breweries, Distilleries, Docks, Ship Decks, Meat Packing, Seafood & Poultry Processing Floors, Stadium Ramps and similar applications. Cannot be compared to off the shelf non slip paints that are single component and very thin. They offer moderate slip protection and inferior durability in commercial or industrial applications. You must use a two-component epoxy designed specifically for these types of wet/caustic, high traffic environments. Otherwise, you are wasting your time and money while creating a potentially hazardous condition.
Applied in one layer at about 1/16"-1/8" dried thickness of protection compared to most other products that are water based and a fraction as thick. Meets OSHA, USDA and ADA requirements. Low odor, nontoxic, superior water, impact, abrasion and chemical resistance. Impervious to oil, grease, alcohol, gasoline, hydraulic fluids, road salts, saltwater exposure and caustic washdown detergents.
Can be applied to concrete and steel floors, indoors or outdoors. Self priming on concrete and steel. For additional adhesion to poor condition concrete, steel and diamond plate applications we recommend priming with our Primer first. Use standard version primer or Fast Dry Primer that dries in 1-2 hours versus 5-7 hours for the standard version. It's also recommended to prime first for applications with a high volume of heavy traffic.
Can be applied over previous coatings that are not peeling off, existing paints and coatings should be sanded clean and roughed up. Can be applied in temperatures down to 30 degrees with Low Temp Version which is much lower than standard non slip flooring paints or epoxies.
This non-skid epoxy is USDA approved and meets ADA and OSHA standards for safe slip resistance, ensuring that when applied correctly, it provides the necessary coefficient of friction for safer walking and working surfaces. This makes it ideal for wet or slippery conditions, where reliable anti-slip performance is essential for maintaining a safe environment.
See our Cove Base kits to provide a seamless transition from floor to wall so that the epoxy can be coated right across the floor and up the wall to form a waterproof tub for easy pressure washing.
This coating is easily applied with phenolic core roller or flat squeegee by in house maintenance staffs, no experience needed for professional results. For heavy texture apply with a phenolic core roller, for a less textured finish apply with flat squeegee. This coating is forklift and rubber track vehicle rated. For rubber wheels and tracks we recommend the flat squeegee application which will have a less aggressive finish and will have increased coverage rate of up to 50 sf/gal. The roller application has a very aggressive finish that can wear out certain soft rubber tires and tracks. When we say it's industrial grade, we mean it!
For a flexible rubber non slip epoxy floor coating see our ArmorTrak Epoxy.
Request A Quote For Volume Discounts.
Apply at 40 sf/gallon. Coverage may vary according to application method and surface porosity. Allow 8 hrs to dry to the touch. Back to service with light traffic within 24hrs depending on temperature and humidity. Allow 48 hours for vehicle traffic.
This is an industrial grade product, Part B has the viscosity similar to Goop (it's very very thick), we like to use a can opener to remove the lip from the top of the can to make it easier to get all of the Part B out. Mix ratio is 4:1 but you can simply pour all of Part B into the Part A can and use a Jiffy mixer in a cordless drill to mix. Mix it till all the Part B is blended into the Part A making sure to move the mixer all around the Part A can.
Once mixed pour in a bead from left to right and apply with phenolic core roller or flat squeegee depending on amount of texture desired. For best results roll or squeegee in one direction as much as possible, avoid back and forth motions. Roller will yield more aggresive finish and squeegee will have less agressive finish. Apply at the average of 40 sf/gal rate. Pot life is 30 minutes. Do not mix more than can be applied in about 20 minutes. Only one coat is required. Finish may have slightly uneven gloss depending on application. This is simply a cosmetic issue and will not effect performance of the product. Product should be left to dry overnight and can be back in full service the next day.
Please note this product should be applied with good ventillation when applying indoors and the use of paint respirator is recommended. Do not apply in the presence of open flames or sparks such as from, Unit Heaters, welding or torch cutting equipment.
Steel should be primed with our Primer for an even thicker finish and to ensure permanent adhesion. Concrete should be acid washed twice with a strong 2 part water to one part muriatic acid solution then nuetralized by sprinkling and lightly scrubbing in 1 lb of TSP powder per 1000 square feet of wet floor and then rinsed thoroughly. Allow floor to completely dry (minimum 24 hrs).
Remove oil stains with a combination of Liquid Tide scrubbed in with striahgt muriatic acid, several applications may be needed depending on how deep the stain is. When water no longer turns a bluish ranibow color or beads up oil has been removed. Alternate prep is diamond grind or shotblasting, this will save time by not having to wait for a wet floor to dry out. All surfaces must clean, dry and free of contaminants.
