Surface Bond Asphalt & Concrete Coating
Tired of black asphalt or pedestrian gray concrete? Surface Bond delivers designer color, fast cure, low odor, and industrial durability for driveways, plazas, malls, pool decks, walkways, bike lanes, parking garages, and more.
Beautiful Color + Serious Protection
Surface Bond works on new or old concrete (patterned or flat) and new or old asphalt. It’s ideal for stamped concrete and lasts far longer than typical stains that wear quickly. It’s also a major upgrade over traditional asphalt emulsion coatings that can be smelly, contain high levels of PAHs, and wear off fast.
It cures in just a few hours for same-day or next-day full service. For public commercial areas, downtime and odor matter — Surface Bond solves both while delivering best-in-class durability.
Each kit includes Part A (in a 5-gallon pail for mixing), Part B activator, and a liquid color tint (your choice). Pour all three into the supplied pail to yield 4 mixed gallons, mix with a mud mixer, and apply by roller or spray. Long working time + fast cure makes it ideal for projects where speed matters.
Textured Walkway Example
Stamped Concrete Done in Tile Red
Two coats are the minimum; more coats increase durability and lifespan. We also offer walkway & bike lane greens in two shades designed for high-mileage traffic.
Surface Bond Features
Surface Bond-HDColor Chart
Click any swatch to zoom โข Actual colors may vary slightly โ request a sample for exact match
Additional colors can be created by mixing various colors together.
Custom colors may be available for large orders โข Contact info@armorgarage.com or call (866) 532-3979
Coverage will vary according to type of surface, texture of surface and age of surface. Coverage will average about 275 sf/ 4 gal pail. If using the textured roller figure 225 sf/4 gal pail. Coverage may vary depending on surface texture, condition, porosity and application thickness.
We recommend two coats for pedestrian traffic and light vehicle traffic, three coats for heavy vehicle traffic such as commercial parking areas or public roadways and traffic crossings. Goes on at an average of 9 mils per coat dried film thickness. Up to five coats can be applied!
Surface Preparation
Surface must be clean and completely dry before application. For asphalt, a good leaf blower and stiff-bristled broom is normally all that's needed โ vigorously broom the surface to loosen dirt, then blow it away.
For very dirty or large surfaces, power wash and allow sufficient drying time. If vehicle fluids are present in the surface, they must be removed. Oil stains can be scrubbed out with Liquid Tide and muriatic acid, then thoroughly rinsed. Allow the surface to dry completely.
Check Weather Conditions
Temperature must remain above 50ยฐF for a minimum of 4 hours after you finish application. No rain is allowed for 24 hours after application.
Primer (If Needed)
For asphalt surfaces, use Surface Bond Primer unless the asphalt is new and stable. Apply Surface Bond after primer is dry to the touch โ about 45 minutes.
For concrete, bricks, or pavers, primer isn't required but is recommended to increase adhesion. If coating over stamped concrete, use a ยฝ"โยพ" nap roller.
Mix the Coating
Surface Bond is a one-component product. Add 1 pint of color per 5-gallon unit. Mix with the Surface Bond metal mixer for 3โ4 minutes to ensure color is evenly distributed.
Apply the Coating
Application method is the same for asphalt and concrete. Once thoroughly mixed, roll on with 3/8" lint-free rollers, or use the Surface Bond roller for an orange-peel textured finish. The coating can also be applied with a flat squeegee, sprayed, or broomed โ depending on the surface.
| Surface Type | Best Method |
|---|---|
| Smooth asphalt or concrete | Roll on with 3/8" lint-free roller |
| Rough textured asphalt | Squeegee to spread, then back-roll to even out |
| Stamped concrete | Spray and broom, or squeegee and broom |
| Bricks and pavers | Spray while a second person brooms into the pattern |
Maintain the recommended coverage rate regardless of application method.
Recoat & Finish
Allow each coat to dry fully to the touch before applying the next. Recoat time is 30โ45 minutes. Dry time for the final coat is 1โ3 hours depending on temperature and humidity.
Roll or spray the second coat perpendicular to the first coat โ this ensures a more even finish. When spraying over a patterned surface, use a broom to work the coating in and distribute it evenly. The final coat on a non-patterned surface can be sprayed and rolled instead of broomed.
Application Examples
Zoom
Zoom
One person sprays while the other works the coating into the pattern with a broom. Smooth surfaces can be simply rolled on.
Zoom
For rough textured asphalt, spread initially with a squeegee then back-roll with a roller to even out the coating.
โข One Year Limited Warranty per coat, up to five coats can be applied. More coats will result in higher durability.
โข Shore D Hardness of 80.8. About equal to construction hard hats!
โข Surface Bond is an ArmorGarage HDSC(High Durability Surface Coating) which means its super durable with an abrasion loss rating of an amazing .33mgs. This means it can handle high volumes of vehicle traffic without wearing out.
โข Superior flexibility allows it to handle applications with large temperature swings. Can handle temperatures from -50 to 150 degrees!
โข Environmentally friendly and nontoxic. Meets all EPA VOC standards. Can be fully recycled with asphalt.
โข Slip resistant for all applications
โข Very user friendly with long pot life and quick curing once applied. Allows for fast back in service turn around in 24 hrs or less.
โข Easily recoatable in the future with just a standard cleaning that is needed as prep.
โขUV stable!
โข Incredibly impact resistant and is even hail resistant.
โข Cannot be compared to typical polyurethane epoxies
โข Large selection of colors
โข No experience needed, easy to apply
โขCan be applied in a smooth finish or textured finish using our textured rollers.
