Extra Heavy Duty Non-Slip Textured Epoxy Coating
The only industrial-grade two-part textured non-slip epoxy thick enough to actually stop slips in wet, caustic, and heavy-traffic environments. Installs at 1/16”–1/8” dried thickness — that’s 5–10x thicker than standard coatings.
USDA Approved • OSHA & ADA Compliant • Navy Mil-Spec PRF-24667BWhy This Non-Slip Epoxy Is in a Completely Different Category
If you’re comparing this to off-the -shelf type non-slip paints, stop — they’re not the same product. Those are single-component coatings that go on paper-thin, don't provide industrial-grade traction, and break down within months under real commercial use. Here’s how they actually compare:
Hardware Store Non-Slip Paint
- Single component, water-based
- 2–4 mils thickness (paper thin)
- Wears through in months
- Minimal chemical resistance
- Not rated for forklift traffic
- 50–60°F minimum application
- No USDA or Mil-Spec ratings
AG650X Non-Slip Epoxy
- Two-component industrial epoxy
- 60–125 mils (1/16”–1/8”) thickness
- Lasts years under heavy traffic
- Full chemical & acid resistance
- Forklift & heavy equipment rated
- Low temp version down to 25°F
- USDA, OSHA, ADA, Navy Mil-Spec
Two texture options: For maximum grip, apply with a phenolic core roller for an aggressive, high-traction surface. For a less aggressive finish (recommended for rubber-wheel and rubber-track vehicles), apply with a flat squeegee — this method also increases coverage up to 50 sf/gal.
What Makes This the Right Choice
Works on Concrete, Steel, and Improves Diamond Plate Traction
Self-priming on concrete and steel. For maximum adhesion on marginal surfaces, diamond plate, or extremely high-traffic areas, prime first with our standard or Fast Dry primer (dries in 1–2 hours vs. 5–7 for standard).
Waterproof Washdown-Ready Surface
Creates an impervious barrier against water, mold, mildew, and bacteria. Add our Cove Base kit for a seamless floor-to-wall seal that turns your floor into a waterproof tub for pressure washing.
Install It Yourself — No Contractor Needed
Complete turnkey kits include everything you need. Apply with a roller or squeegee in a single coat. Available in 1-gallon and 5-gallon sizes. Coverage: 30–40 sf/gal (roller) or 40–50 sf/gal (squeegee).
Where This Coating Gets Installed
Available in 1-gallon and 5-gallon kits • Custom fills in 5-gal pails (50-gal minimum — call for pricing)
Priming & Surface Preparation
For maximum adhesion on poor-condition concrete, heavily used diamond plate, prime first. Choose the standard concrete primer or the steel primer.
Can be applied directly over existing coatings that are still bonded and not peeling — sand the surface clean and rough it up first. Works indoors and outdoors.
Cove Base Option: Our Cove Base kits create a seamless floor-to-wall transition so the epoxy coats across the floor and up the wall, forming a waterproof tub for easy pressure washing. Ideal for kitchens, processing plants, and any washdown environment.
Rubber wheels & tracks: Use the flat squeegee application for a less aggressive texture and increased coverage. The roller method produces a very aggressive profile that can accelerate wear on soft rubber tires and tracks.
Steel & metal surfaces: While this epoxy bonds directly to steel, any exposed bare metal can develop surface rust (“freckle rusting”). Priming with our Metal & Steel Industrial Coating eliminates this issue entirely and ensures a bulletproof bond.
Want to see and feel the texture before you buy? Contact our sales team to request a physical sample piece.
Looking for a flexible rubber non-slip coating instead? See our ArmorTrak Rubber Textured Epoxy — ideal for areas requiring a softer, rubber-like texture.
Request A Quote for volume discounts on orders of 50+ gallons.
Free Shipping on Orders $300+
Complete turnkey kits with everything needed for professional results. No contractor required — no prior experience needed.
Call: (866) 532-3979 | Email: info@armorgarage.com
Apply at 40 sf/gallon. Coverage may vary according to application method and surface porosity. Allow 8 hrs to dry to the touch. Back to service with light traffic within 24hrs depending on temperature and humidity. Allow 48 hours for vehicle traffic.
Application Instructions
Mixing
This is an industrial grade product. Part B has a viscosity similar to Goop — it’s extremely thick. We recommend using a can opener to remove the lip from the top of the Part B can to make it easier to get all the material out.
Mix ratio is 4:1, but you can simply pour all of Part B into the Part A can and use a Jiffy mixer in a cordless drill. Mix until all the Part B is fully blended into the Part A, making sure to move the mixer all around the can.
Pot life is 30 minutes. Do not mix more than can be applied in about 20 minutes. Only one coat is required.
Application
Once mixed, pour in a bead from left to right and apply with a phenolic core roller or flat squeegee depending on the amount of texture desired.
Roller application: Yields a more aggressive, heavily textured finish. Coverage is 30–40 sq ft/gal.
Squeegee application: Yields a less aggressive, smoother finish. Coverage is 40–50 sq ft/gal. Recommended for rubber wheel and track vehicles.
For best results, roll or squeegee in one direction as much as possible — avoid back and forth motions. Apply at the average rate of 40 sq ft/gal. Finish may have slightly uneven gloss depending on application; this is purely cosmetic and will not affect performance.
Drying & Return to Service
Product should be left to dry overnight and can be back in full service the next day.
Safety & Ventilation
Good ventilation is required when applying indoors. The use of a paint respirator is recommended.
Do NOT apply in the presence of open flames or sparks such as from unit heaters, welding, or torch cutting equipment.
Surface Preparation
Steel Surfaces
Steel should be clean with no rust or contaminants present on the surface ; if not it should be primed with our Steel Primer that can adhere to tight rust for an even thicker finish and to ensure permanent adhesion.
Concrete Surfaces
Acid wash twice with a strong solution of 2 parts water to 1 part muriatic acid. Then neutralize by sprinkling and lightly scrubbing in 1 lb of TSP powder per 1,000 sq ft of wet floor, then rinse thoroughly. Allow the floor to completely dry (minimum 24 hours).
Faster alternative: Diamond grind or shotblast the surface. This saves significant time by eliminating the wet floor dry-out period.
Oil Stain Removal
Remove oil stains with a combination of Liquid Tide scrubbed in with straight muriatic acid. Several applications may be needed depending on how deep the stain is. When water no longer turns a bluish rainbow color or beads up, the oil has been removed.
All surfaces must be clean, dry, and free of contaminants before application.
Need Help With Your Project?
Our expert team is available to help with product selection, surface prep questions, and installation support.
Call: (866) 532-3979 | Email: support@armorgarage.com
