Architect-Designer-Epoxy Floor-Specifications
Floor Coating Specifications for Engineers & Architects
CSI MasterFormat specification sheets ready to copy into your bid package. Each spec covers materials, performance requirements, chemical resistance, surface preparation, and execution — all in standard “shall” language. Select the system that matches your project below.
Heavy Tonnage Epoxy — HVTN100X
100% Solids Polyester/Aliphatic Epoxy • 30 mil Single Coat • Shore D 90
Our highest-performance floor coating. A single 30-mil coat delivers extreme abrasion resistance (2.5 mg Taber loss), 420 psi adhesion, and 160 in-lb impact resistance. Withstands heavy rolling loads, chemical spills, and continuous industrial traffic. Roll-on application, full cure in 2–4 days.
Military-Industrial Epoxy Floor System
3-Layer System: Epoxy Primer + 100% Solids Epoxy + Military Grade Topcoat • 20+ mil Total DFT
Three-layer roll-on epoxy system consisting of a penetrating epoxy primer (ARM144X), 100% solids high-build epoxy base coat (ARM707X), and military-grade polyurethane topcoat (ARM356X). Delivers 20–40+ mils total DFT, 450 psi adhesion, 4.0 mg Taber abrasion loss on topcoat, 160 in-lb impact resistance, and excellent UV stability. Full cure in 3–7 days.
ArmorGarage II — Commercial Epoxy Floor System
2-Layer System: Solids Epoxy Base Coat + Urethane-Fortified Topcoat • 12+ mil Total DFT • Shore D 80
Two-layer roll-on commercial epoxy system consisting of a 100% solids pigmented epoxy base coat (8–10 mils DFT) and a urethane-fortified high-wear topcoat (3–4 mils DFT) with UltraWear non-slip additive. Delivers 12+ mils total DFT, 375 psi adhesion ( concredte failure prior to delamination), 12,000 psi compressive strength, 160 in-lb impact resistance, and excellent UV stability. USDA approved for food prep areas. Hot tire resistant. Full cure in 2-3 days.
Commercial Kitchen & Processing Epoxy — HV100X
100% Solids Polyester/Aliphatic Epoxy • 30 mil Single Coat • Shore D 90
High-performance single-coat epoxy engineered for commercial kitchens, food processing areas, packaging lines, and cafeterias. A single 30-mil coat delivers extreme abrasion resistance (2.5 mg Taber loss), 420 psi adhesion, and 160 in-lb impact resistance. Chemical resistant, suitable for caustic washdowns, and meets sanitary facility requirements. Roll-on application, full cure in 2 days.
Urethane Slurry Mortar — AG903SLX
Bio-Based Urethane Cement • 1/8”–3/16” Thickness • Shore D 80 • Heat Resistant to 200°F
Bio-based urethane slurry mortar engineered for areas requiring thermal shock resistance and heavy-duty chemical protection. Installs at 1/8” to 1/4” thickness, delivers 8,400 psi compressive strength, 160 in-lb impact resistance, and withstands temperatures up to 200°F. Resistant to MVT, fungi growth, and aggressive chemicals including 50% sodium hydroxide and 30% sulfuric acid. Seamless hygienic finish with no grout lines. Suitable for caustic washdowns. Full cure in 24 hours.
Extra Heavy Duty Epoxy — DATN100X — Data Center & Semiconductor Manufacturing Floors
100% Solids Polyester/Aliphatic Epoxy • 30 mil Single Coat • Shore D 90 • Low VOC <0.5 g/L
Industry-specific specification for data centers, colocation facilities, and semiconductor fabs. A single 30-mil coat delivers extreme abrasion resistance (2.5 mg Taber loss) for wheeled server rack transport, 420 psi adhesion (concrete failure), and D-rated chemical resistance to battery electrolyte, coolants, and diesel fuel. Low VOC (<0.5 g/L) minimizes outgassing in controlled environments. Seamless, non-porous finish supports cleanroom protocols. Includes specifier notes for ESD grounding, raised floor coordination, battery room containment, and phased installation for mission-critical uptime. Full cure in 2 days.
Heavy Duty Novolac Epoxy System — AG253X / AG257X
High-Solids Novolac Primer + Topcoat • 425 psi Adhesion • Shore D 88 • Long-Term Acid Immersion
Two-component novolac epoxy system engineered for heavy-duty acid and chemical resistance. The AG257X primer provides 375 psi adhesion with excellent substrate penetration, while the AG253X topcoat delivers 9,900 psi compressive strength, 425 psi adhesion, and long-term immersion resistance (E-rated) to sulfuric acid, sodium hydroxide, and hydrochloric acid. System provides a seamless, chemical-impervious barrier for bund flooring, secondary containment areas, chemical troughs, and curb coatings. Ideal for environments requiring protection against concentrated acid spills, solvent exposure, and aggressive chemical washdowns. Total system build of 21–23 mils. Full cure 2–7 days.
Standard Duty Chemical & Acid Resistant Epoxy — AG257X
Novolac Epoxy • 2-Coat System • 8–10 mils DFT • 375 psi Adhesion • Low Odor
Cost-effective novolac epoxy applied in two coats for standard-duty acid and chemical exposure environments. Delivers E-rated long-term immersion resistance to sulfuric acid (10%), sodium hydroxide (10% & 50%), hydrochloric acid (10%), and ethylene glycol — plus D-rated 72-hour immersion resistance to xylene, toluene, and gasoline. Two coats build 8–10 mils DFT with 375 psi adhesion, low odor, and satin-gloss finish. No separate primer required. Ideal where full novolac topcoat system is not needed but chemical protection exceeds what standard epoxies can provide. Suitable for caustic washdowns and sanitary environments.
High Build Wet Surface Epoxy — AGARM-591X
100% Solids Cycloaliphatic Epoxy • Wet & Underwater Application • Zero VOC • 40–120°F
Moisture-insensitive 100% solids cycloaliphatic epoxy that can be applied directly on wet surfaces or fully underwater. Two-coat system delivers 10–14 mils total DFT with zero VOC (unthinned). Low-modulus flexible film will not lift or crack over existing sound coatings. Self-priming on steel and concrete. Application range of 40–120°F with dry service temperature of 30–180°F. Apply by spray, roller, or brush at 230–320 sf/gal per coat. Optional UltraWear non-slip additive for slip-resistant finish. Full cure 7 days.
Heavy-Duty Non-Skid Epoxy — AG650X
94% Solids Textured Epoxy • 1/32″–1/16″ DFT • Mil PRF 24667B Offset • Low Temp Cure Available
Two-component heavy-duty non-skid epoxy at 94% solids designed for industrial and marine environments. Builds 1/32″–1/16″ textured film in a single coat for superior slip resistance in wet, oily, and high-traffic conditions. Chemical resistant to aviation fuel, jet fuel, diesel, hydraulic fluid, sodium hydroxide 25%, lactic acid, and salt water. Application by phenolic core roller (30–40 sf/gal) or squeegee/trowel (40–50 sf/gal). Regular cure 50–120°F; low temp cure version available down to 40°F for cold-weather applications. Excellent coating for diamond plate. Service temperature to 160°F. Full cure 3–5 days. VOC < 74 g/L.
Interlocking Floor Tiles — Heavy-Duty PVC Tile System
4.5mm–7mm PVC • No Adhesives • Class 1 Fire Rated • Shore A 92 • >45 KV Dielectric
Heavy-duty PVC interlocking tiles engineered for high-traffic commercial and industrial environments. Install directly over existing concrete, VCT, or hard surfaces with no adhesives, no curing time, and no facility disruption. Precision dovetail, T-joint, or hidden joint systems provide a secure, gapless floor. 2,700 psi tensile strength, Shore A 92 hardness, Class 1 fire rating (ANSI/ASTM E648 / NFPA 253), dielectric strength exceeding 45 KV, and chemical resistance to acids, solvents, and fuels. Anti-static ESD available on 6.5mm and 7mm models. Sound absorption up to 48 dB. UV stable. Available in 8 tile profiles across multiple colors and textures.
Chemical Mastic High Build Steel Epoxy — AGCM15X
82% Solids Epoxy Mastic • Self-Priming on Steel • USDA Approved • 6–10 mils DFT • 170°F Service
High-solids amine-cured epoxy mastic engineered for steel and metal substrates. Self-priming with excellent adhesion over marginally prepared surfaces where full blast cleaning is impractical or prohibited. 82% solids by volume, 5–7 mils DFT per coat at 188–263 sf/gal. Chemical resistant to 57+ chemicals including sodium hydroxide 50%, sulfuric acid 20%, jet fuel, xylene, and petroleum products. USDA approved. Apply by airless spray, conventional spray, brush, or roller. Suitable as standalone finish or high-build primer under polyurethane (AGARM-370) or acrylic topcoats. Low temp cure version available down to 45°F. Service temperature to 170°F. VOC 161 g/L unthinned.
ArmorTrak V1 — Military Grade Flexible Polyurethane Coating
1-Part Moisture-Cured • 30–40 Mils Total (2 Coats) • COF 0.91 Dry / 0.62 Wet • Indoor/Outdoor
Single-component moisture-cured polyurethane with embedded recycled rubber granules for a tough, slip-resistant, waterproof membrane. Totally flexible — never chips, flakes, or peels. Bonds to concrete, wood, fiberglass, metal, rubber, asphalt, and sound-painted surfaces. 100% salt water resistant with freeze-thaw range of −60°F to 254°F. Fire resistance ASTM E-162: 01. COF 0.91 dry / 0.62 wet. Coverage 200–225 sf/gal for a 2-coat system at 24–30 mils DFT. Walk time 6–12 hours, full cure ±4 days. Apply by roller, brush, or spray at 32–95°F. Available in 15+ standard colors plus custom matching. Smooth (no granules) and aliphatic UV-stable (ArmorTrak 18) versions available. VOC 2.08 lbs/gal.
Copolymer Roof Coating — ARM814
Copolymer Liquid Rubber • 20–22 mil DFT • 500% Elongation • UL Class A
Single-component copolymer liquid rubber membrane for tar-based, EPDM, APP, TPO, and Hypalon roofs. Delivers 1,000 psi tensile strength, 82.5 solar reflectance, and 9,000-hour QUV weathering with no degradation. Two-coat application at 100 sf/gal per coat achieves a seamless, flexible waterproofing membrane. Meets Federal VOC requirements.
Metal Roof Coating — ARM812X
Acrylic Liquid Rubber • 20–22 mil DFT • 500% Elongation • UL Class A
Single-component acrylic liquid rubber membrane specifically formulated for metal roofs. Strong adhesion to anodized metals and painted surfaces. Delivers 1,000 psi tensile strength, 82.5 solar reflectance, and superior low temperature flexibility. Two-coat application at 100 sf/gal per coat creates a seamless waterproofing barrier. Meets Federal VOC requirements.
Need a project-specific specification? Contact us at 866-532-3979 or info@armorgarage.com and we’ll work with your design team to create custom specifications for your bid package.